Crush and run gravel is made from tiny pieces of gravel that is mixed with limestone. This is a useful top layer for gravel driveways because the limestone sticks together when wet, helping the driveway last longer. Crush and run gravel driveways are affordable and can last for years if they are properly maintained.
Depending upon your
wheelbarrow size (i.e. 2 or 3 cubic feet per
wheelbarrow load), it will take 9 to 14 full loads to equal 1 cubic yard.
How many yards is 5 tons?
| Ton Register [ton Reg] | Cubic Yard [yd^3] |
|---|
| 10 ton reg | 37.037037037 yd^3 |
| 20 ton reg | 74.0740740741 yd^3 |
| 50 ton reg | 185.1851851852 yd^3 |
Gravel 1-1/2” to 2” will need to be 3” deep, and 2” to 4” gravel needs to be 4” deep. This is to provide complete coverage and so you cannot see the landscape fabric (weed-mat) through the gaps in the gravel.
These are the best options for driveway surfaces gravel, because they are small stones combined with rock dust, which makes a more solid driving surface.
- Crushed Stone #411. It is crushed up #57 stone combined with rock dust.
- Quarry Process.
- Pea Gravel.
- Jersey Shore Gravel.
- Marble Chips.
- Blackstar or Blacktrap Rock.
Measuring the DrivewayTo measure the driveway in cubic feet, multiply the length by width by depth. For cubic yards, divide the total cubic feet by 27. Because one cubic yard of gravel is equal to 1.13 tons, you can multiply your total cubic yards by 1.13 to convert this measurement to tons.
The depth of the gravel can vary, but should be at least 4 to 6 inches. To determine this measurement in feet, divide the number of inches by 12 (for example, 6 inches is 0.5 feet). If you plan to do two to three layers, each layer will need to be 4 to 6 inches thick, so you will to calculate each layer separately.
1 cubic yard of gravel weight is 2800 lb, in United States, 1 ton of gravel is equal to 2000 pounds, convert tons of gravel to cubic yards = 2000/2800 = 0.714 cubic yards, so there are 0.714 cubic yards in a ton of gravel.
A truck load of gravel costs $1,350 or more with a 10-yard minimum, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
A cubic yard measures volume where a ton measures weight. A yard of topsoil usually weighs about 1,800 pounds and a yard of gravel usually weighs about 2,200 pounds.
If you want to cover an area with gravel, 1 to 2 inches should be sufficient depending on the size of the gravel. If you are using 3/4" inch gravel or larger figure on at least 2 inches in depth to get good coverage.
General rule of thumb to work out the amount of pebble you will need is to allow 70-80Kg per square meter. The depth of coverage would be at the minimum end of the scale at this meterage. If you have pavers to consider add up the total area and subtract the amount of paving you have bought/laid.
Gravel, Regular weighs 1.35 gram per cubic centimeter or 1 346 kilogram per cubic meter, i.e. density of gravel, Regular is equal to 1 346 kg/m³. In Imperial or US customary measurement system, the density is equal to 84.03 pound per cubic foot [lb/ft³], or 0.78 ounce per cubic inch [oz/inch³] .
How much is a yard of gravel? To calculate the weight of the material, you simply have to multiply the volume by the density.
Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This will tell you how many cubic yards of crushed stone you need. When using this equation, make sure all of your measurements are in feet.
Measure the length, width and depth in feet of the area to be covered. Multiply the three numbers together. Divide by 27 to get the number of cubic yards of pea gravel needed. For example, if the area is 9 feet square and the gravel is to be a foot deep, multiply 9 by 9 by 1 to get 81.
Density of 20mm and 40mm aggregate ranging between 1450 kg/m3 to 1550 kg/m3, consider density of 20mm aggregate is equal to 1550 kg/m3, it means weight of 1 cubic metre of 20 mm size aggregate is equal to 1550 kg.
1 t = 1000 m3. You also can convert 1 Tons (metric) to other Weight (popular) units.
Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.
As a rule of thumb 1 of our 25kg bags will cover an area of 0.25m to a recommended depth of 50mm.
Consider a ½ cubic foot bag of stone or soil weighs about 50 lbs and will cover 2 square feet at 3" deep. A bag of hardwood or cedar bark contains about 1 cubic foot of material, enough to cover about 4 square feet at 3" deep. If you have large areas you probably need bulk.
You need 14.13 cubic feet of gravel for the fire pit. Add 10 percent to the total to give yourself a little extra gravel in case you need it. Ten percent of 14.13 cubic feet is an additional 1.4 feet, bringing the total amount of gravel you need to 15.5 cubic feet.
Put down the base layer. Gravel composed of 3/4-inch crushed rock pieces mixed with rock dust works best. The crushed rock will add stability to the top layer of pea gravel. Use a garden rake to spread the material evenly to a depth of about 2 inches.
